Tsutsumi IMPACIII TS-711 Controller
Tsutsumi IMPACIII TS-711 Controller
The Tsutsumi IMPACIII TS-711 is an automatic controller for soldering. It has a 32 bit micro-computer for controls. It reads and writes data using the RS-323C communication port. It enables registering of up to 31 soldering conditions. These conditions check for the length and end of the soldering wire, clogging of solder, temperature of soldering iron tip, and so on. In case of any problem, the controller stops the soldering operation and sends the error message to the output device.
The solder length to be fed can be set from 0 to 99.9mm or 0 to 999mm. The solder feeding speed can be set from
0 to 99.9mm/sec. The soldering time can be set from 0 to 9.99sec or 0 to 999.9sec. Optionally use the computer software TSCOWin to manage the data required for soldering on a computer.
This is the controller of the easy operation type which attached our original temp. control program.
- IMPAC III /TS-711 is an automatic soldering controller unit developed in order to enable automatic point and slide soldering.
- This controller, has 31 soldering conditions, includes checking function of solder wire end/shortage, solder clogging, temperature down of soldering iron tip and broken wire/disconnection of temperature sensor.
- When once irregularity happened, it stops soldering cycle operation and sends error output signal to external I/O and signal communication port.
- Since the controller, FEEDER and IRON unit are all compact or separated each other, it is possible to make their layout and wiring efficiently.
Features
- 31 programmable conditions soldering controller.
- Reading and writing data are possible via the communication port and also multi condition can operate by replacing data
- One host PC can read and write programs of up t0 10 sets of IMPAC III
- (Optional interface TW-611 is required in this case).
- Condition of cleaning can be set.
- Solder wire feeding unit can be changed to 0.1mm or 1mm.
- Timer set unit can be changed to 0.01sec or 0.1 sec.
Function
- Solder Feeding
- Solder wire can be supplied up to 99.9mm max. in length in 0.1mm unit.
- Solder wire can be supplied up to 999mm max. in length in 1mm unit.
- Either can be Selected
- Heating Timer
- Heating time can be set up to 9.99sec max. in 0.01sec unit.
- Heating time can be set up to 99.9sec max. in 0.1sec unit.
- Temperature Set of Soldering Tip
- The temperature can be set between 0 °C and 500 °C (32°F~932°F) in 1 °C step.
- As auto tuning function is integrated, the optimum P, I, D factor can be set automatically to keep stable the set temperature for soldering iron tip.
- Heating Timer
- Slide Soldering
- Additional “ACK” (signal to robot can be started), “Slide end” (signal can be stopped solder feeding at any time) can operate slide soldering.
- Communication (Multiplex communication)
- It is possible to select one of 31 different soldering patterns and soldering tip temperature setting by an external microcomputer through RS-232C.
- (Optional TSCO is requested.)
- And controller monitoring is also available by monitor command.
- A setup serves as easy operation of inputting each numerical value.
- The setting is an easy operation only of the input of each numerical value.
Specifications
Model No. | TS-711 | |
Weight | 2kg | |
Power Requirement | AC100V – 240V ± 10%, 50/60Hz | |
Power Consumption | 30W+ (Heater Capacity) | |
Working Ambient Temperature | 0 – 50°C (No Condensation) | |
Working Environment | No Corrosive Gas | |
Control System | 32-Bit Micro-Computer | |
Number Of Control Axes | 1 Control | |
Number Of Programs | 31 | |
Programming System / Temp Setup | Panel Key, RS232C | |
Operating Sequence | Fixed | |
Temperature Control System | PID Method | |
Temperature Setting Range | 0 – 500°C (32 – 932°F) | |
Setting Value | Solder Feeding Amount : 0~99.9mm or 0~999mm | |
Solder Feeding Speed: 0~99.9mm/sec | ||
Timer: 0~9.99sec or 0~99.9sec | ||
Control Signal | *Input | Start, Stop, Cleaning, Reset |
Slide end , Manual solder feeding, standby temp release, iron down | ||
Selection of soldering conditions (4-bit) |
Why Choose Sumitron ?