Hakko FR-810B Rework Station
Hakko FR-810B Rework Station
Hakko FR 810 is a turbine powered digital SMD hot air rework station. It can provide hot air with a temperature of up to 600 Degree Celsius having and having airflow of up to 115L/min. The right amount of airflow and air temperature can be achieved using the digital controls. This allows it to be used on low density board to high density boards. The rework station has a simple procedure for removing the nozzle and is easily maintainable. You can use conventional nozzles with FR 810 using a conversion adapter. The temperature range for this station is between 50 Degree Celsius to 600 Degree Celsius and the airflow speed ranges from 5 L/min to 115 L/min.
High power and large air volume. Further evolution of SMD rework station
Features
- High power and large volume hot air for quick removal of components
A tool that can provide powerful hot airflow for repairing high heat capacity circuit boards that require high blow volume and high output, and sufficient hot airflow for appropriate blow volume and high output for high-density mounting substrates.
- Efficiency Improvement
The FR-810B’s high volume airflow and high output make it possible to perform the same work in only one-third of the time required when using a conventional model. This reduces the thermal impact on boards and components.
* Examination of time taken for connector sections soldered onto a ceramic board to be heated to 200°C with maximum temperature and airflow settings selected. * Single nozzles with an approximately 4mm diameter were used. |
- Improvements of FR-810B
On top of the features of FR-810, high power and large air volume, the new functions of vacuum pickup and pickup indicator have been given to FR-810B.
The 2 new functions make it possible to remove a component without damaging PWB.
|
|
The new nozzle improves work efficiency with uniform heating by hot air convection inside the nozzle which is created due to vents on the nozzle top. (Only with BGA nozzle) | |
|
|
The vacuum pickup function is to pick up a component with a suction pad and vacuum. It will pick a component only after the hot air melts solder joints. This can avoid an error to peel off the land by removing a component with excessive force. |
|
|
|
By pre-setting pickup function, a component can be picked up automatically when solder is melted. Then, the indication comes up and the moment of picking up will be visible. Even a component and solder joints can not be seen as covered by a nozzle, easy and safe picking up is possible. |
- Use conventional HAKKO nozzles
Align the projection part, attach the conventional nozzle to the heater pipe.
The heater pipe of HAKKO FR-810 (discontinued) has two projection parts. In order to use the conventional nozzle, put the conversion adaptor on the heater pipe that was included in your purchased HAKKO FR-810 as one of standard accessories.
|
- Simple nozzle removal and easy maintenance
Nozzles can be quickly changed for many different types of components.
In addition, conventional nozzles are compatible. Heaters can also be easily and securely replaced.
Quick-change N51 nozzles | Simple heater replacement |
Simple, tool-free removal and attachment. | Simply remove four screws to replace heater. |
- Timer Function
A new timer function allows for repeatably consistent work times.
This can help to prevent parts from overheating and can improve the overall quality of your work.
- Chain presets function for making a simple thermal profile
The chain presets function is to make a simple thermal profile by combining several preset conditions. (Up to 5 steps) This can improve work efficiency a lot by standardizing work time, avoiding overheating, improving repeatability of operation, and making difficult rework jobs easy.
- Auto sleep and auto shutoff features
To ensure safety and conserve power, when the handpiece is placed in the handpiece holder, the auto sleep function is activated and it starts cooling automatically. If the handpiece has not been removed from the handpiece holder (Ex. Using it in a rework fixture) and after it has been idle for 30 minutes, auto shutoff function is activated. It is automatically powered off. Access to settings can be restricted via the password function for easy management. |
- With the use of Grip fixture, Board holder and Bottom heater, work conditions can be controlled even more strictly.
A low cost rework system can be assembled with a bottom heater, a grip fixture, and a board holder.
HOT AIR REWORK STATION
Model No. | FR-810B |
Power Consumption | AC100V:700W AC110V:840W AC120V:820W AC220V:1,100W AC230V:1,200W AC240V:1,300W |
Temperature Range | 50 to 600ºC |
Station
Power Consumption | 30W |
Air Flow | 1-9 (5 to 115L/min) |
Dimensions | 160(W)×145(H)×220(D)mm |
Weight | 1.5kg |
Handpiece (Hot air)
Power Consumption | AC100V:670W AC110V:810W AC120V:790W AC220V:1,070W AC230V:1,170W AC240V:1,270W |
Standard Nozzle | Φ4mm (No.N51-02) |
Total Length | 250mm |
Weight | 180g |
* Dimensions and weight for station (w/o cord, iron holder assembly)
* Total length and weight for handpiece (w/o cord, standard nozzle)
* Airflow capacity is rated as free flowing. Restrictions created by various nozzles may reduce the maximum airflow capacity.
Industries Powered By Soldering Stations
Why Choose Sumitron ?